Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
What are your ideas with regards to How to Install a Bathtub?
Installing a bath tub isn't precisely brain surgery, however it does need strong plumbing, carpentry, and also in some cases, tiling skills. Changing an old tub with a new one is likewise a moderately tough job. If the old tub is readily accessible, the job can move speedily; if you have to open up a wall to eliminate the old bathtub as well as place the brand-new bathtub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly require a helper to vacate the old tub as well as embeded in the brand-new one. Ensure you have actually qualified on your own for the work and also fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly assist you install a new bath tub in your washroom if you have already acquired a brand-new tub and also don't require to change the arrangement of your previous water supply pipes.
Your devices and material list should consist of the following:
Planning for the Installation
To start with, the sustaining framework provided with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you should do is detach the supply of water. After doing so, activate the faucets to drain any water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome as a result of the limited accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the staying water that will originate from the pipes. Once the supply pipelines have actually been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Before going on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, place the tub in the called for position. The wood boards are practical in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the bath tub till the level checks out degree.
To mount taps, fit all-time low of the furthest adaptable faucet adapter to the ideal supply pipeline by making a compression join; then do the same for the various other tap.
Turn on the water and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill up the tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bathtub has actually been utilized at least when as this will settle it right into its final position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Secure the faucet in position with the maker provided backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap ports. The former type ought to be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a stiff seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, bring about issues with moisture and possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to permit the movement experienced when the bathtub is in usage. The sealer can split rather very early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly offered on the marketplace. It is advisable to fit the tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about Installing A Bathtub? Give feedback below. We'd be glad to find out your thinking about this posting. In hopes to see you back again in the future. Do you know another individual who is enthusiastic about How to Install a Bathtub Yourself? Be sure share it. We value reading our article about A Step-by-Step Guide to Installing a Bathtub.
Top-notch fix? Dial! Report this page